From 8b2219bfa2da36e7809588ef723a10483a6e137f Mon Sep 17 00:00:00 2001 From: Francis Rowe Date: Thu, 6 Nov 2014 01:52:36 +0000 Subject: Documentation: *major* cleanup. Cleanup was long overdue. Old structure was messy and inefficient. --- docs/hardware/x60_heatsink.html | 144 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 144 insertions(+) create mode 100644 docs/hardware/x60_heatsink.html (limited to 'docs/hardware/x60_heatsink.html') diff --git a/docs/hardware/x60_heatsink.html b/docs/hardware/x60_heatsink.html new file mode 100644 index 00000000..1e14f964 --- /dev/null +++ b/docs/hardware/x60_heatsink.html @@ -0,0 +1,144 @@ + + + + + + + + + Libreboot documentation: Switch heatsink on ThinkPad X60 + + + + +
+

Changing the fan/heatsink on the ThinkPad X60

+ +
+ +

Or go back to main index

+ +

Table of Contents

+ + +

Hardware requirements

+ + +

Software requirements (for CPU stress testing)

+ + +

Disassembly

+

+ Remove those screws:
+ +

+

+ Push the keyboard forward (carefully):
+ +

+

+ Lift the keyboard up and disconnect it from the board:
+ +

+

+ Grab the right-hand side of the chassis and force it off (gently) and pry up the rest of the chassis:
+ +

+

+ You should now have this:
+ +

+

+ Disconnect the wifi antenna cables, the modem cable and the speaker:
+ +

+

+ Unroute the cables along their path, carefully lifting the tape that holds them in place. Then, disconnect the modem + cable (other end) and power connection and unroute all the cables so that they dangle by the monitor hinge on the right-hand + side:
+ +

+

+ Disconnect the monitor from the motherboard, and unroute the grey antenna cable, carefully lifting the tape + that holds it into place:
+ +

+

+ Carefully lift the remaining tape and unroute the left antenna cable so that it is loose:
+ +

+

+ Remove those screws:
+ +

+

+ Remove those screws:
+ +

+

+ Carefully remove the plate, like so:
+ +

+

+ Remove the SATA connector:
+ +

+

+ Now remove the motherboard (gently) and cast the lcd/chassis aside:
+ +

+

+ Look at that black tape above the heatsink, remove it:
+ +

+

+ Now you have removed it:
+ +

+ +

+ Disconnect the fan and remove all the screws, heatsink will easily come off:
+ +

+ +

+ Remove the old paste with a cloth (from the CPU and heatsink) and then clean both of them with the alcholeel (to remove remaining residue. typo is intentional). + Apply a pea-sized amount of paste to the both chipsets that the heatsink covered and spread it evenly (uniformally). + Finally reinstall the heatsink, reversing previous steps. +

+ +

+ stress -c 2 command can be used to push the CPU to 100%, and xsensors (or watch sensors command) can be used to monitor heat. + Below 90C is ok. +

+ +
+ +

+ Copyright © 2014 Francis Rowe <info@gluglug.org.uk>
+ This document is released under the Creative Commons Attribution-ShareAlike 4.0 International Public License and all future versions. + A copy of the license can be found at ../license.txt. +

+ +

+ This document is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See ../license.txt for more information. +

+ + + -- cgit v1.2.3-70-g09d2