ThinkPad T500: flashing tutorial (BeagleBone Black)
***************************************************

Flashing the T500 with a BeagleBone Black
*****************************************

Initial flashing instructions for T500.

This guide is for those who want libreboot on their ThinkPad T500 while they still have the original Lenovo BIOS present. This guide can also be followed (adapted) if you brick your T500, to know how to recover.

Back to main index (index.html)

Libreboot T400
**************

You may also be interested in the smaller, more portable Libreboot T400 (t400_external.html).

Serial port
===========

EHCI debug might not be needed. It has been reported that the docking station for this laptop has a serial port, so it might be possible to use that instead.

LCD compatibly
**************

Not all LCD panels are compatible yet. See ../hcl/gm45_lcd.html.

A note about CPUs
*****************

ThinkWiki (http://www.thinkwiki.org/wiki/Category:T500) has a list of CPUs for this system. The Core 2 Duo P8400, P8600 and P8700 are believed to work in libreboot. The T9600 was also tested on the T400 and confirmed working, so the T9400/T9500/T9550 probably also work, but they are untested.

Quad-core CPUs
==============

Incompatible. Do not use.

A note about GPUs
*****************

Some models have an Intel GPU, while others have both an ATI and an Intel GPU; this is referred to as "switchable graphics". In the BIOS setup program for lenovobios, you can specify that the system will use one or the other (but not both).

Libreboot is known to work on systems with only the Intel GPU, using native graphics initialization. On systems with switchable graphics, the Intel GPU is used and the ATI GPU is disabled, so native graphics initialization works all the same.

CPU paste required
******************

See #paste.

Flash chip size
***************

Use this to find out:
 # dmidecode | grep ROM\ Size

Back to top of page.

MAC address
***********

On the T500, the MAC address for the onboard gigabit ethernet chipset is stored inside the flash chip, along with other configuration data.

Keep a note of the MAC address before disassembly; this is very important, because you will need to insert this into the libreboot ROM image before flashing it. It will be written in one of these locations:

Initial BBB configuration
*************************

Refer to bbb_setup.html for how to configure the BBB for flashing.

The following shows how to connect clip to the BBB (on the P9 header), for SOIC-16 (clip: Pomona 5252):

POMONA 5252 (correlate with the BBB guide)
===  ethernet jack and VGA port ====
 NC              -       - 21
 1               -       - 17
 NC              -       - NC
 NC              -       - NC
 NC              -       - NC
 NC              -       - NC
 18              -       - 3.3V (PSU)
 22              -       - NC - this is pin 1 on the flash chip
===  SATA port ===
This is how you will connect. Numbers refer to pin numbers on the BBB, on the plugs near the DC jack.

The following shows how to connect clip to the BBB (on the P9 header), for SOIC-8 (clip: Pomona 5250):

POMONA 5250 (correlate with the BBB guide)
===  RAM slots ====
 18              -       - 1
 22              -       - NC
 NC              -       - 21
 3.3V (PSU)      -       - 17 - this is pin 1 on the flash chip
===  slot where the AC jack is connected ===
This is how you will connect. Numbers refer to pin numbers on the BBB, on the plugs near the DC jack.

The procedure
=============

Remove all screws:

 It is also advisable to, throughout the disassembly, place any screws and/or components that you removed in the same layout or arrangement. The follow photos demonstrate this:

Remove the HDD/SSD and optical drive:

Remove the palm rest:

Remove the keyboard and rear bezel:

If you have a WWAN/3G card and/or sim card reader, remove them permanently. The WWAN-3G card has proprietary firmware inside; the technology is identical to what is used in mobile phones, so it can also track your movements:

Remove this frame, and then remove the wifi chip:

Remove the speakers:

Remove the NVRAM battery (already removed in this photo):

When you re-assemble, you will be replacing the wifi chip with another. These two screws don't hold anything together, but they are included in your system because the screw holes for half-height cards are a different size, so use these if you will be installing a half-height card:

Unroute the antenna wires:

Disconnect the LCD cable from the motherboard:

Remove the LCD assembly hinge screws, and then remove the LCD assembly:

Remove the fan and heatsink:

Remove this screw:

Remove these cables, keeping note of how and in what arrangement they are connected:

Disconnect the power jack:

Remove the motherboard and cage from the base (the marked hole is where those cables were routed through):

Remove all screws, arranging them in the same layout when placing the screws on a surface and marking each screw hole (this is to reduce the possibility of putting them back in the wrong holes):

Also remove this:

Separate the motherboard from the cage:

The flash chip is next to the memory slots. On this system, it was a SOIC-8 (4MiB or 32Mb) flash chip:

Connect your programmer, then connect GND and 3.3V

A dedicated 3.3V PSU was used to create this guide, but at ATX PSU is also fine:

Of course, make sure to turn on your PSU:

Now, you should be ready to install libreboot.

Flashrom binaries for ARM (tested on a BBB) are distributed in libreboot_util. Alternatively, libreboot also distributes flashrom source code which can be built.

Log in as root on your BBB, using the instructions in bbb_setup.html#bbb_access.

Test that flashrom works:
 # ./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512
 In this case, the output was:

flashrom v0.9.7-r1854 on Linux 3.8.13-bone47 (armv7l)
flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OK.
Found Macronix flash chip "MX25L6405(D)" (8192 kB, SPI) on linux_spi.
Found Macronix flash chip "MX25L6406E/MX25L6436E" (8192 kB, SPI) on linux_spi.
Found Macronix flash chip "MX25L6445E/MX25L6473E" (8192 kB, SPI) on linux_spi.
Multiple flash chip definitions match the detected chip(s): "MX25L6405(D)", "MX25L6406E/MX25L6436E", "MX25L6445E/MX25L6473E"
Please specify which chip definition to use with the -c <chipname> option.

How to backup factory.rom (change the -c option as neeed, for your flash chip):
 # ./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512 -r factory.rom
 # ./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512 -r factory1.rom
 # ./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512 -r factory2.rom
 Note: the -c option is not required in libreboot's patched flashrom, because the redundant flash chip definitions in flashchips.c have been removed.
 Now compare the 3 images:
 # sha512sum factory*.rom
 If the hashes match, then just copy one of them (the factory.rom) to a safe place (on a drive connected to another system, not the BBB). This is useful for reverse engineering work, if there is a desirable behaviour in the original firmware that could be replicated in coreboot and libreboot.

Follow the instructions at ../hcl/gm45_remove_me.html#ich9gen to change the MAC address inside the libreboot ROM image, before flashing it. Although there is a default MAC address inside the ROM image, this is not what you want. Make sure to always change the MAC address to one that is correct for your system.

Now flash it:
 # ./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512 -w path/to/libreboot/rom/image.rom -V

You might see errors, but if it says Verifying flash... VERIFIED at the end, then it's flashed and should boot. If you see errors, try again (and again, and again); the message Chip content is identical to the requested image is also an indication of a successful installation.

Example output from running the command (see above):

flashrom v0.9.7-r1854 on Linux 3.8.13-bone47 (armv7l)
flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OK.
Found Macronix flash chip "MX25L6405(D)" (8192 kB, SPI) on linux_spi.
Reading old flash chip contents... done.
Erasing and writing flash chip... FAILED at 0x00001000! Expected=0xff, Found=0x00, failed byte count from 0x00000000-0x0000ffff: 0xd716
ERASE FAILED!
Reading current flash chip contents... done. Looking for another erase function.
Erase/write done.
Verifying flash... VERIFIED.

Back to top of page.

Thermal paste (IMPORTANT)
*************************

Because part of this procedure involved removing the heatsink, you will need to apply new paste. Arctic MX-4 is ok. You will also need isopropyl alcohol and an anti-static cloth to clean with.

When re-installing the heatsink, you must first clean off all old paste with the alcohol/cloth. Then apply new paste. Arctic MX-4 is also much better than the default paste used on these systems.

NOTE: the photo above is for illustration purposes only, and does not show how to properly apply the thermal paste. Other guides online detail the proper application procedure.

Wifi
****

The T500 typically comes with an Intel wifi chipset, which does not work without proprietary software. For a list of wifi chipsets that work without proprietary software, see ../hcl/index.html#recommended_wifi.

Some T500 laptops might come with an Atheros chipset, but this is 802.11g only.

It is recommended that you install a new wifi chipset. This can only be done after installing libreboot, because the original firmware has a whitelist of approved chips, and it will refuse to boot if you use an 'unauthorized' wifi card.

The following photos show an Atheros AR5B95 being installed, to replace the Intel chip that this T500 came with:

WWAN
****

If you have a WWAN/3G card and/or sim card reader, remove them permanently. The WWAN-3G card has DMA, and proprietary firmware inside; the technology is identical to what is used in mobile phones, so it can also track your movements.

Not to be confused with wifi (wifi is fine).

Memory
******

You need DDR3 SODIMM PC3-8500 RAM installed, in matching pairs (speed/size). Non-matching pairs won't work. You can also install a single module (meaning, one of the slots will be empty) in slot 0.

Make sure that the RAM you buy is the 2Rx8 density.

The following photo shows 8GiB (2x4GiB) of RAM installed:

Boot it!
========

You should see something like this:

Now install GNU/Linux (../gnulinux/index.html).

Copyright © 2015 Francis Rowe <info@gluglug.org.uk>
 Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.3 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts, and no Back-Cover Texts. A copy of the license can be found at gfdl-1.3.txt (../resources/licenses/gfdl-1.3.txt)

Updated versions of the license (when available) can be found at https://www.gnu.org/licenses/licenses.html

UNLESS OTHERWISE SEPARATELY UNDERTAKEN BY THE LICENSOR, TO THE EXTENT POSSIBLE, THE LICENSOR OFFERS THE LICENSED MATERIAL AS-IS AND AS-AVAILABLE, AND MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND CONCERNING THE LICENSED MATERIAL, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHER. THIS INCLUDES, WITHOUT LIMITATION, WARRANTIES OF TITLE, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, ABSENCE OF LATENT OR OTHER DEFECTS, ACCURACY, OR THE PRESENCE OR ABSENCE OF ERRORS, WHETHER OR NOT KNOWN OR DISCOVERABLE. WHERE DISCLAIMERS OF WARRANTIES ARE NOT ALLOWED IN FULL OR IN PART, THIS DISCLAIMER MAY NOT APPLY TO YOU.

TO THE EXTENT POSSIBLE, IN NO EVENT WILL THE LICENSOR BE LIABLE TO YOU ON ANY LEGAL THEORY (INCLUDING, WITHOUT LIMITATION, NEGLIGENCE) OR OTHERWISE FOR ANY DIRECT, SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY, OR OTHER LOSSES, COSTS, EXPENSES, OR DAMAGES ARISING OUT OF THIS PUBLIC LICENSE OR USE OF THE LICENSED MATERIAL, EVEN IF THE LICENSOR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES, COSTS, EXPENSES, OR DAMAGES. WHERE A LIMITATION OF LIABILITY IS NOT ALLOWED IN FULL OR IN PART, THIS LIMITATION MAY NOT APPLY TO YOU.

The disclaimer of warranties and limitation of liability provided above shall be interpreted in a manner that, to the extent possible, most closely approximates an absolute disclaimer and waiver of all liability.