diff options
Diffstat (limited to 'docs/bsd/openbsd.md')
| -rw-r--r-- | docs/bsd/openbsd.md | 26 |
1 files changed, 13 insertions, 13 deletions
diff --git a/docs/bsd/openbsd.md b/docs/bsd/openbsd.md index 284f0468..783bd7bb 100644 --- a/docs/bsd/openbsd.md +++ b/docs/bsd/openbsd.md @@ -11,7 +11,7 @@ LibertyBSD and prioritise that in this guide. This section relates to preparing, booting and installing OpenBSD on your libreboot system, using nothing more than a USB flash drive (and -*dd*). They\'ve only been tested on a Lenovo ThinkPad x200. +*dd*). They've only been tested on a Lenovo ThinkPad x200. - [Prepare the USB drive (in OpenBSD)](#prepare) - [Installing OpenBSD without full disk encryption](#noencryption) @@ -44,7 +44,7 @@ Connect the USB drive. Check dmesg:\ Check to confirm which drive it is, for example, if you think its sd3:\ **\$ disklabel sd3** -Check that it wasn\'t automatically mounted. If it was, unmount it. For +Check that it wasn't automatically mounted. If it was, unmount it. For example:\ **\$ doas umount /dev/sd3i**\ @@ -85,7 +85,7 @@ Connect the USB drive. Check dmesg:\ Check lsblk to confirm which drive it is:\ **\$ lsblk** -Check that it wasn\'t automatically mounted. If it was, unmount it. For +Check that it wasn't automatically mounted. If it was, unmount it. For example:\ **\$ sudo umount /dev/sdX\***\ **\# umount /dev/sdX\*** @@ -141,7 +141,7 @@ to boot a truly fully encrypted OpenBSD or LibertyBSD installation, by putting everything in the flash chip.** Alternatively, modifying GRUB to support booting fully encrypted OpenBSD -installations would be possible, but probably not feasible; it\'s an +installations would be possible, but probably not feasible; it's an alien codebase to the OpenBSD project, not tightly integrated and the OpenBSD bootloader already works. @@ -166,22 +166,22 @@ OpenBSD will start booting. Yay! Configuring Grub ---------------- -If you don\'t want to drop to the GRUB command line and type in a +If you don't want to drop to the GRUB command line and type in a command to boot OpenBSD every time, you can create a GRUB configuration -that\'s aware of your OpenBSD installation and that will automatically +that's aware of your OpenBSD installation and that will automatically be used by libreboot. On your OpenBSD root partition, create the **/grub** directory and add the file **libreboot\_grub.cfg** to it. Inside the **libreboot\_grub.cfg** add these lines: -**default=0 timeout=3 menuentry \"OpenBSD\" {\ +**default=0 timeout=3 menuentry "OpenBSD" {\ kopenbsd -r sd0a (ahci0,openbsd1)/bsd\ }\ ** -The next time you boot, you\'ll see the old Grub menu for a few seconds, -then you\'ll see the a new menu with only OpenBSD on the list. After 3 +The next time you boot, you'll see the old Grub menu for a few seconds, +then you'll see the a new menu with only OpenBSD on the list. After 3 seconds OpenBSD will boot, or you can hit enter to boot. [Back to top of page](#pagetop). @@ -191,16 +191,16 @@ seconds OpenBSD will boot, or you can hit enter to boot. Troubleshooting =============== -Most of these issues occur when using libreboot with coreboot\'s \'text -mode\' instead of the coreboot framebuffer. This mode is useful for +Most of these issues occur when using libreboot with coreboot's 'text +mode' instead of the coreboot framebuffer. This mode is useful for booting payloads like memtest86+ which expect text-mode, but for OpenBSD it can be problematic when they are trying to switch to a framebuffer -because it doesn\'t exist. +because it doesn't exist. In most cases, you should use the vesafb ROM images. Example filename: libreboot\_ukdvorak\_vesafb.rom. -won\'t boot\...something about file not found +won't boot\...something about file not found --------------------------------------------- Your device names (i.e. usb0, usb1, sd0, sd1, wd0, ahci0, hd0, etc) and |