diff options
Diffstat (limited to 'docs/hardware/t60_heatsink.md')
-rw-r--r-- | docs/hardware/t60_heatsink.md | 42 |
1 files changed, 28 insertions, 14 deletions
diff --git a/docs/hardware/t60_heatsink.md b/docs/hardware/t60_heatsink.md index 824fb8b1..a2fcd914 100644 --- a/docs/hardware/t60_heatsink.md +++ b/docs/hardware/t60_heatsink.md @@ -28,21 +28,26 @@ Software requirements {#software_requirements} Disassembly {#recovery} =========== -Remove those screws and remove the HDD:\ +Remove those screws and remove the HDD: + ![](../images/t60_dev/0001.JPG) ![](../images/t60_dev/0002.JPG) -Lift off the palm rest:\ +Lift off the palm rest: + ![](../images/t60_dev/0003.JPG) Lift up the keyboard, pull it back a bit, flip it over like that and -then disconnect it from the board:\ +then disconnect it from the board: + ![](../images/t60_dev/0004.JPG) ![](../images/t60_dev/0005.JPG) ![](../images/t60_dev/0006.JPG) -Gently wedge both sides loose:\ +Gently wedge both sides loose: + ![](../images/t60_dev/0007.JPG) ![](../images/t60_dev/0008.JPG) -Remove that cable from the position:\ +Remove that cable from the position: + ![](../images/t60_dev/0009.JPG) ![](../images/t60_dev/0010.JPG) Remove the bezel (sorry forgot to take pics). @@ -50,7 +55,8 @@ Remove the bezel (sorry forgot to take pics). On the CPU (and there is another chip south-east to it, sorry forgot to take pic) clean off the old thermal paste (with the alcohol) and apply new (Artic Silver 5 is good, others are good too) you should also clean -the heatsink the same way\ +the heatsink the same way + ![](../images/t60_dev/0051.JPG) This is also an opportunity to change the CPU to another one. For @@ -59,33 +65,41 @@ processor (higher speed, 64-bit support). A Core 2 Duo T7600 was installed here. Attach the heatsink and install the screws (also, make sure to install -the AC jack as highlighted):\ +the AC jack as highlighted): + ![](../images/t60_dev/0052.JPG) -Reinstall that upper bezel:\ +Reinstall that upper bezel: + ![](../images/t60_dev/0053.JPG) -Do that:\ +Do that: + ![](../images/t60_dev/0054.JPG) ![](../images/t60_dev/0055.JPG) -Attach keyboard:\ +Attach keyboard: + ![](../images/t60_dev/0056.JPG) Place keyboard and (sorry, forgot to take pics) reinstall the palmrest -and insert screws on the underside:\ +and insert screws on the underside: + ![](../images/t60_dev/0058.JPG) -It lives!\ +It lives! + ![](../images/t60_dev/0071.JPG) ![](../images/t60_dev/0072.JPG) ![](../images/t60_dev/0073.JPG) Always stress test ('stress -c 2' and xsensors. below 90C is ok) when -replacing cpu paste/heatsink:\ +replacing cpu paste/heatsink: + ![](../images/t60_dev/0074.JPG) -Copyright © 2014, 2015 Leah Rowe <info@minifree.org>\ +Copyright © 2014, 2015 Leah Rowe <info@minifree.org> + Permission is granted to copy, distribute and/or modify this document under the terms of the Creative Commons Attribution-ShareAlike 4.0 International license or any later version published by Creative |