diff options
Diffstat (limited to 'docs/hcl/d945gclf.md')
| -rw-r--r-- | docs/hcl/d945gclf.md | 64 |
1 files changed, 25 insertions, 39 deletions
diff --git a/docs/hcl/d945gclf.md b/docs/hcl/d945gclf.md index ebb22e0a..a537996c 100644 --- a/docs/hcl/d945gclf.md +++ b/docs/hcl/d945gclf.md @@ -1,4 +1,6 @@ -% Intel D945GCLF desktop board + +Intel D945GCLF desktop board +============================ [Back to previous index](https://libreboot.org/docs/hcl/) @@ -37,63 +39,47 @@ Remarks about vendor bios: flashing to install libreboot on this device. Once libreboot is flashed there is no problem to update the firmware internally -Here is an image of the board: - - - -Here is an image of the D945GCLF2 board: - -{width="80%" height="80%"} +Here is an image of the board:\ +\ +Here is an image of the D945GCLF2 board:\ +{width="80%" height="80%"}\ +And SPI SOIC8 flash chip\ +{width="50%" height="50%"} -And SPI SOIC8 flash chip -{width="50%" height="50%"} How to replace thermal paste and fan ------------------------------------ This board comes with very crappy disposable loud fan, that one has no bearings, which can not be repaired or oiled properly, do not waste your -time trying to fix it, just buy one chinese same size fan - +time trying to fix it, just buy one chinese same size fan\ {width="50%" height="50%"} -{width="50%" height="50%"} - -Make sure that new one has same wiring - -{width="50%" height="50%"} - -This is a new one, with bearing and maintenable - +{width="50%" height="50%"}\ +Make sure that new one has same wiring\ +{width="50%" height="50%"}\ +This is a new one, with bearing and maintenable\ {width="50%" height="50%"} -{width="50%" height="50%"} - +{width="50%" height="50%"}\ Now remove the both coolers rotating them a bit, slowly, then clean both -silicons and both coolers (removing cmos battery first is recommended) - -{width="50%" height="50%"} - +silicons and both coolers (removing cmos battery first is recommended)\ +{width="50%" height="50%"}\ Put a little bit of non conductive thermal paste on both silicons (only -cpu silicon iis shown on that image) - -{width="50%" height="50%"} +cpu silicon iis shown on that image)\ +{width="50%" height="50%"}\ Before assembling new fan, some need new longer screws, make sure having -these (on the left is original one, too short for new fan) - -{width="50%" height="50%"} - -After that, assemble your new fan into CPU cooler - -{width="50%" height="50%"} - +these (on the left is original one, too short for new fan)\ +{width="50%" height="50%"}\ +After that, assemble your new fan into CPU cooler\ +{width="50%" height="50%"}\ Finally assemle both coolers on both chips, do not forget put in the CPU fan connector back, and you are done. -Copyright © 2016 Arthur Heymans <arthur@aheymans.xyz> -Copyright © 2016 Vitaly Castaño Solana <vita\_cell@hotmail.com> +Copyright © 2016 Arthur Heymans <arthur@aheymans.xyz>\ +Copyright © 2016 Vitaly Castaño Solana <vita\_cell@hotmail.com>\ Permission is granted to copy, distribute and/or modify this document under the terms of the Creative Commons Attribution-ShareAlike 4.0 International license or any later version published by Creative |