13 files changed, 18 insertions, 14 deletions
diff --git a/docs/install/bbb_setup.md b/docs/install/bbb_setup.md
index 18f0c7be..94cfdc0b 100644
--- a/docs/install/bbb_setup.md
+++ b/docs/install/bbb_setup.md
@@ -40,7 +40,7 @@ Shopping list (pictures of this hardware is shown later):
     (rev. C) is highly recommended. You can buy one from
     [Adafruit](https://www.adafruit.com) (USA),
     [ElectroKit](http://electrokit.com) (Sweden) or any of the
-    distributors listed [here](http://beagleboard.org/black) (look below
+    distributors listed on [BeagleBoard's website](http://beagleboard.org/black) (look below
     'Purchase'). We recommend this product because we know that it
     works well for our purposes and doesn't require any non-free
     software.
@@ -328,7 +328,10 @@ PSU to pin 2 on the BBB (P9 header). It is safe to install this now
 should.*
 
 if you need to extend the 3.3v psu leads, just use the same colour M-F
-leads, *but* keep all other leads short (10cm or less)
+leads, *but* keep all other leads short and equal length (30cm or less).
+Keep in mind that length isn't inversely proportional to signal quality,
+so trying out different lengths will yield different results.
+Same goes for spispeed.
 
 You should now have something that looks like this:\
 ![](images/x200/5252_bbb0.jpg) ![](images/x200/5252_bbb1.jpg)
diff --git a/docs/install/images/rpi/0003.png b/docs/install/images/rpi/0003.png
index fa090cf1..c7a3b9b2 100644
--- a/docs/install/images/rpi/0003.png
+++ b/docs/install/images/rpi/0003.png
diff --git a/docs/install/images/rpi/0009.png b/docs/install/images/rpi/0009.png
index d3293069..130536b0 100644
--- a/docs/install/images/rpi/0009.png
+++ b/docs/install/images/rpi/0009.png
diff --git a/docs/install/images/rpi/0010.png b/docs/install/images/rpi/0010.png
index e989afa4..312888e9 100644
--- a/docs/install/images/rpi/0010.png
+++ b/docs/install/images/rpi/0010.png
diff --git a/docs/install/images/rpi/0011.png b/docs/install/images/rpi/0011.png
index fa090cf1..c7a3b9b2 100644
--- a/docs/install/images/rpi/0011.png
+++ b/docs/install/images/rpi/0011.png
diff --git a/docs/install/images/rpi/0012.png b/docs/install/images/rpi/0012.png
index d3293069..130536b0 100644
--- a/docs/install/images/rpi/0012.png
+++ b/docs/install/images/rpi/0012.png
diff --git a/docs/install/images/rpi/0013.png b/docs/install/images/rpi/0013.png
index e989afa4..312888e9 100644
--- a/docs/install/images/rpi/0013.png
+++ b/docs/install/images/rpi/0013.png
diff --git a/docs/install/images/x200/disassembly/0007.jpg b/docs/install/images/x200/disassembly/0007.jpg
deleted file mode 100644
index 68bfb28a..00000000
--- a/docs/install/images/x200/disassembly/0007.jpg
+++ /dev/null
diff --git a/docs/install/images/x200/x200_soic16.jpg b/docs/install/images/x200/x200_soic16.jpg
new file mode 100644
index 00000000..345a04d7
--- /dev/null
+++ b/docs/install/images/x200/x200_soic16.jpg
diff --git a/docs/install/images/x200/x200_soic8.jpg b/docs/install/images/x200/x200_soic8.jpg
new file mode 100644
index 00000000..59adfabd
--- /dev/null
+++ b/docs/install/images/x200/x200_soic8.jpg
diff --git a/docs/install/index.md b/docs/install/index.md
index 70dd554e..f2a70112 100644
--- a/docs/install/index.md
+++ b/docs/install/index.md
@@ -264,13 +264,13 @@ executables from the libreboot source code archives.
 
 How to update the flash chip contents:
 
-    $ sudo ./flash update [yourrom.rom](#rom)
+`$ sudo ./flash update `[`yourrom.rom`](#rom)
 
 Ocassionally, coreboot changes the name of a given board. If flashrom
 complains about a board mismatch, but you are sure that you chose the
 correct ROM image, then run this alternative command:
 
-    $ sudo ./flash forceupdate [yourrom.rom](#rom)
+ `$ sudo ./flash forceupdate `[`yourrom.rom`](#rom)
 
 You should see `Verifying flash... VERIFIED.` written at the end
 of the flashrom output. *Shut down* after you see this, and then boot
@@ -303,7 +303,7 @@ the flashing script. do this: *
 
 The first half of the procedure is as follows:
 
-    $ sudo ./flash i945lenovo\_firstflash [yourrom.rom](#rom).
+`$ sudo ./flash i945lenovo_firstflash `[`yourrom.rom`](#rom)
 
 You should see within the output the following:
 
@@ -330,13 +330,11 @@ needed (see below).
 
 When you have booted up again, you must also do this:
 
-    $ sudo ./flash i945lenovo\_secondflash [yourrom.rom](#rom)
+`$ sudo ./flash i945lenovo_secondflash `[`yourrom.rom`](#rom)
 
 If flashing fails at this stage, try the following:
 
-    # sudo ./flashrom/i686/flashrom -p
-
-internal:laptop=force\_I\_want\_a\_brick -w [yourrom.rom](#rom)
+`$ sudo ./flashrom/i686/flashrom -p internal:laptop=force_I_want_a_brick -w `[`yourrom.rom`](#rom)
 
 You should see within the output the following:
 
@@ -372,7 +370,7 @@ with your device.
 
 Use this flashing script, to install libreboot:
 
-    $ sudo ./flash i945apple\_firstflash [yourrom.rom](#rom)
+`$ sudo ./flash i945apple_firstflash `[`yourrom.rom`](#rom)
 
 You should also see within the output the following:
 
diff --git a/docs/install/t400_external.md b/docs/install/t400_external.md
index b4b1ece3..8f34f4c5 100644
--- a/docs/install/t400_external.md
+++ b/docs/install/t400_external.md
@@ -12,7 +12,7 @@ An
 ["HMM"](https://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles_pdf/43y6629_05.pdf#page=386)
 (Hardware Maintenance Manual) detailing the process of \[dis\]assembly
 is available for this model. Be careful when reassembling the laptop as
-the screws on page 144 (with title "1130 Keyboard bezel") are swapped
+the screws on page 114 (with title "1130 Keyboard bezel") are swapped
 and if you follow the HMM you will punch a hole through the bezel in the
 upper right corner.
 
diff --git a/docs/install/x200_external.md b/docs/install/x200_external.md
index 6414fe7c..3ff34501 100644
--- a/docs/install/x200_external.md
+++ b/docs/install/x200_external.md
@@ -17,13 +17,13 @@ GNU+Linux distribution.
 Flash chip size
 ===============
 
-Use this to find out:
+Run this command on x200 to find out flash chip model and its size:
 
     # flashrom -p internal -V
 
 The X200S and X200 Tablet will use a WSON-8 flash chip, on the bottom of the
 motherboard (this requires removal of the motherboard). Not all X200S/X200T are
-supported; see [here](../hardware/x200.html#x200s).
+supported; see the [hardware](../hardware/x200.html#x200s) page.
 
 MAC address
 ===========
@@ -108,9 +108,12 @@ lifting up the left and right side of it:\
 ![](images/x200/disassembly/0006.1.jpg)
 ![](images/x200/disassembly/0006.jpg)
 
+This shows the location of the flash chip, for both SOIC-8 and SOIC-16:\
+![](images/x200/x200_soic16.jpg)
+![](images/x200/x200_soic8.jpg)
+
 Lift back the tape that covers a part of the flash chip, and then
 connect the clip:\
-![](images/x200/disassembly/0007.jpg)
 ![](images/x200/disassembly/0008.jpg)
 
 On pin 2 of the BBB, where you have the ground (GND), connect the ground