diff options
author | Leah Rowe <info@minifree.org> | 2017-04-29 17:13:18 +0000 |
---|---|---|
committer | Gogs <gogitservice@gmail.com> | 2017-04-29 17:13:18 +0000 |
commit | ee9449d8bdac8954278d34f5a150a87083f6a4c7 (patch) | |
tree | 5bbdd502b7a003cc357d4d25ba5da3e4370ac176 /docs/install | |
parent | da31f31721864c8953558ba4e8e7a440e88ea861 (diff) | |
parent | c9552f78f48c3a6f0108c7bb21ee6411458708af (diff) | |
download | librebootfr-ee9449d8bdac8954278d34f5a150a87083f6a4c7.tar.gz librebootfr-ee9449d8bdac8954278d34f5a150a87083f6a4c7.zip |
Merge branch 'master' of swiftgeek/libreboot into master
Diffstat (limited to 'docs/install')
-rw-r--r-- | docs/install/bbb_setup.md | 18 | ||||
-rw-r--r-- | docs/install/x200_external.md | 14 |
2 files changed, 4 insertions, 28 deletions
diff --git a/docs/install/bbb_setup.md b/docs/install/bbb_setup.md index af9026b3..30e4adc7 100644 --- a/docs/install/bbb_setup.md +++ b/docs/install/bbb_setup.md @@ -327,24 +327,6 @@ leads, **but** keep all other leads short (10cm or less) You should now have something that looks like this:\ ![](images/x200/5252_bbb0.jpg) ![](images/x200/5252_bbb1.jpg) -Notes about stability {#stability} -===================== - -<http://flashrom.org/ISP> is what we typically do in libreboot, though -not always. That page has some notes about using resistors to affect -stability. Currently, we use spispeed=512 (512kHz) but it is possible to -use higher speeds while maintaining stability. - -tty0\_ in \#libreboot was able to get better flashing speeds with the -following configuration: - -- "coax" with 0.1 mm core and aluminum foley (from my kitchen), add - 100 Ohm resistors (serial) -- put heatshrink above the foley, for: CS, CLK, D0, D1 -- Twisted pair used as core (in case more capacitors are needed) -- See this image: <http://i.imgur.com/qHGxKpj.jpg> -- He was able to flash at 50MHz (lower speeds are also fine). - Copyright © 2014, 2015 Leah Rowe <info@minifree.org>\ Copyright © 2015 Patrick "P. J." McDermott <pj@pehjota.net>\ Copyright © 2015 Albin Söderqvist\ diff --git a/docs/install/x200_external.md b/docs/install/x200_external.md index adcc473b..5f46c3d2 100644 --- a/docs/install/x200_external.md +++ b/docs/install/x200_external.md @@ -92,17 +92,11 @@ header), for SOIC-8 (clip: Pomona 5250): chip on those pins? **On the X200S and X200 Tablet the flash chip is underneath the board, -in a WSON package. The pinout is very much the same as a SOIC-8, except -you need to solder (there are no clips available).\ -The following image shows how this is done:**\ -![](images/x200/wson_soldered.jpg "Copyright 2014 Steve Shenton <sgsit@libreboot.org> see license notice at the end of this document")\ -In this image, a pin header was soldered onto the WSON. Another solution -might be to de-solder the WSON-8 chip and put a SOIC-8 there instead. +in a WSON package. The pinout is very much the same as a SOIC-8, but such package makes it impossible to use testclip. +In order to enable external flashing of device, chip has to be changed to SOIC-8 one. Such procedure requires hot air station and soldering station (with "knife" K-Tip to easily solder SOIC-8).\ Check the list of SOIC-8 flash chips at -[../hardware/gm45\_remove\_me.html\#flashchips](../hardware/gm45_remove_me.md#flashchips) -but do note that these are only 4MiB (32Mb) chips. The only X200 SPI -chips with 8MiB capacity are SOIC-16. For 8MiB capacity in this case, -the X201 SOIC-8 flash chip (Macronix 25L6445E) might work. +[List of supported flash chips](https://www.flashrom.org/Supported_hardware#Supported_flash_chips)\ +25XX series SPI NOR Flash in 8/16MiB sizes will work fine with libreboot. The procedure ------------- |