diff options
Diffstat (limited to 'i18n/fr_FR/docs/hardware/d945gclf.md')
| -rw-r--r-- | i18n/fr_FR/docs/hardware/d945gclf.md | 83 |
1 files changed, 83 insertions, 0 deletions
diff --git a/i18n/fr_FR/docs/hardware/d945gclf.md b/i18n/fr_FR/docs/hardware/d945gclf.md new file mode 100644 index 00000000..f464e4bd --- /dev/null +++ b/i18n/fr_FR/docs/hardware/d945gclf.md @@ -0,0 +1,83 @@ +--- +title: Intel D945GCLF desktop board +... + +If you just want flashing instructions, go to +[../install/d945gclf.md](../install/d945gclf.md) + +This board is a mini-itx desktop board for 2008. It uses an atom 230, +which is a singe core CPU but it is hyperthreaded so it appears to have +2 thread to the OS. The flash chip is very small, 512KiB, so grub2 does +not fit, which is why libreboot has to use seabios on this target. Full +disk encryption like on other supported targets will not be possible, so +plan accordingly. + +This board has a 945gc chipset which is the desktop equivalent of 945gm +which can be found in the Lenovo x60/t60 or macbook2,1. This chipset +features an ICH7 southbridge. It has 1 DIMM slot that can accommodate up +to 2G of DDR2 RAM. + +Connectivity-wise it has 1 PCI slot, a 10/100 ethernet port, 4 usb slot +and 4 usb ports, with one internal header and 2 SATA ports. + +The D945GCLF2 is an upgraded version of this board. The differences are: +1 more USB header, 10/100/1000 ethernet and a dual core cpu (also +hyperthreaded). Since the board is almost identical (and coreboot code +seem to indicate that it works, since MAX\_CPU=4 is set), it is believed +that it should also work but this is untested. + +Remarks about vendor bios: +-------------------------- + +- Without coreboot/libreboot this board is utery useless, since the + vendor bios is very bad. It cannot boot from any HDD whether it is + connected to the SATA port or USB. With libreboot it works just + fine. + +- The vendor bios write protects the flash so it requires external + flashing to install libreboot on this device. Once libreboot is + flashed there is no problem to update the firmware internally + +Here is an image of the board:\ +\ +Here is an image of the D945GCLF2 board:\ +{width="80%" height="80%"}\ +And SPI SOIC8 flash chip\ +{width="50%" height="50%"} + +How to replace thermal paste and fan +------------------------------------ + +This board comes with very crappy disposable loud fan, that one has no +bearings, which can not be repaired or oiled properly, do not waste your +time trying to fix it, just buy one chinese same size fan\ +{width="50%" height="50%"} +{width="50%" height="50%"}\ +Make sure that new one has same wiring\ +{width="50%" height="50%"}\ +This is a new one, with bearing and maintenable\ +{width="50%" height="50%"} +{width="50%" height="50%"}\ +Now remove the both coolers rotating them a bit, slowly, then clean both +silicons and both coolers (removing cmos battery first is recommended)\ +{width="50%" height="50%"}\ +Put a little bit of non conductive thermal paste on both silicons (only +cpu silicon iis shown on that image)\ +{width="50%" height="50%"}\ + +Before assembling new fan, some need new longer screws, make sure having +these (on the left is original one, too short for new fan)\ +{width="50%" height="50%"}\ +After that, assemble your new fan into CPU cooler\ +{width="50%" height="50%"}\ +Finally assemle both coolers on both chips, do not forget put in the CPU +fan connector back, and you are done. + +Copyright © 2016 Arthur Heymans <arthur@aheymans.xyz>\ +Copyright © 2016 Vitaly Castaño Solana <vita\_cell@hotmail.com>\ + +Permission is granted to copy, distribute and/or modify this document +under the terms of the GNU Free Documentation License Version 1.3 or any later +version published by the Free Software Foundation +with no Invariant Sections, no Front Cover Texts, and no Back Cover Texts. +A copy of this license is found in [../fdl-1.3.md](../fdl-1.3.md) |