diff options
Diffstat (limited to 'resources/grub/config')
| -rw-r--r-- | resources/grub/config/menuentries/common.cfg | 24 |
1 files changed, 10 insertions, 14 deletions
diff --git a/resources/grub/config/menuentries/common.cfg b/resources/grub/config/menuentries/common.cfg index 3739b457..9c9c8c17 100644 --- a/resources/grub/config/menuentries/common.cfg +++ b/resources/grub/config/menuentries/common.cfg @@ -33,10 +33,8 @@ menuentry 'Load Operating System (incl. fully encrypted disks) [o]' --hotkey='o # b) Try MBR/GPT partitions at last, one might still conviniently uses a single partition # prompt user for passphrase if LUKS header is found - for d in md/0 ahci0 ahci1; do cryptomount ${d}; done - for j in 1 2 3 4 5 6 7 8 9; do - for d in ahci0 ahci1; do cryptomount "${d},${j}"; done - done + for d in md/0 ahci0; do cryptomount ${d}; done + for j in 1 2 3 4 5 6 7 8 9; do cryptomount "ahci0,${j}"; done # (This way, we only need to scan for encrypted data once while covering every possible disk setup, # be it BTRFS/ZFS/ext4/etc. (on LUKS) (on RAID) on/across raw devices/MBR/GPT @@ -44,9 +42,9 @@ menuentry 'Load Operating System (incl. fully encrypted disks) [o]' --hotkey='o # 2. Look for user config. If the above routine successfully decrypted a LUKS container, its content # will be searched before everything else for obvious reasons. Regardless of this, the devices' # hirachy stays the same. - for d in crypto0 md/0 ahci0 ahci1; do switch_to_grub_config ${d}; done + for d in crypto0 md/0 ahci0; do switch_to_grub_config ${d}; done for j in 1 2 3 4 5 6 7 8 9; do - for d in crypto0 ahci0 ahci1; do switch_to_grub_config "${d},${j}"; done + for d in crypto0 ahci0; do switch_to_grub_config "${d},${j}"; done done # prompt user for passphrase if LUKS header is found but try using external keyfiles first @@ -75,13 +73,11 @@ menuentry 'Load Operating System (incl. fully encrypted disks) [o]' --hotkey='o done } menuentry 'Parse ISOLINUX menu (AHCI) [a]' --hotkey='a' { - for i in 0 1; do - # Check for filesystem on raw device without partition table (MBR/GPT), e.g. BTRFS or ZFS - parse_isolinux_config ahci${i} - # Look for partitions - # GPT allows more than 4 partitions, /boot on /dev/sda7 is quite unlikely but still possible - for j in 0 1 2 3 4 5 6 7 8 9; do parse_isolinux_config "ahci${i},${j}"; done - done + # Check for filesystem on raw device without partition table (MBR/GPT), e.g. BTRFS or ZFS + parse_isolinux_config ahci0 + # Look for partitions + # GPT allows more than 4 partitions, /boot on /dev/sda7 is quite unlikely but still possible + for j in 0 1 2 3 4 5 6 7 8 9; do parse_isolinux_config "ahci0,${j}"; done } menuentry 'Parse ISOLINUX menu (USB) [u]' --hotkey='u' { for i in 0 1; do @@ -101,7 +97,7 @@ menuentry 'Switch to grubtest.cfg [t]' --hotkey='t' { configfile /grubtest.cfg } menuentry 'Search for GRUB configuration (grub.cfg) outside of CBFS [s]' --hotkey='s' { - for i in usb0 usb1 ahci0 ahci1; do + for i in usb0 usb1 ahci0; do for j in 1 2 3 4 5 6 7 8 9; do x=${i},${j} for p in "grub" "boot/grub" "grub2" "boot/grub2"; do |