1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
|
<!DOCTYPE html>
<html>
<head>
<meta charset="utf-8">
<meta name="viewport" content="width=device-width, initial-scale=1">
<style type="text/css">
@import url('../css/main.css');
</style>
<title>ThinkPad X60: Recovery guide</title>
</head>
<body>
<div class="section">
<h1>ThinkPad X60: Recovery guide</h1>
<p>This section documents how to recover from a bad flash that prevents your ThinkPad X60 from booting.</p>
<p><a href="index.html">Back to previous index</a></p>
</div>
<div class="section">
<h1>Table of Contents</h1>
<ul>
<li>
Types of brick:
<ul>
<li><a href="#bucts_brick">Brick type 1: bucts not reset</a></li>
<li><a href="#recovery">Brick type 2: bad rom (or user error), system won't boot</a></li>
</ul>
</li>
</ul>
</div>
<div class="section">
<h1 id="bucts_brick">Brick type 1: bucts not reset.</h1>
<p>
You still have Lenovo BIOS, or you had libreboot running and you flashed another ROM; and you had bucts 1 set and
the ROM wasn't dd'd.* or if Lenovo BIOS was present and libreboot wasn't flashed.<br/><br/>
In this case, unbricking is easy: reset BUC.TS to 0 by removing that yellow cmos coin (it's a battery) and putting it back after a minute or two:<br/>
<img src="../images/x60_unbrick/0004.jpg" alt="" /><br/><br/>
*Those dd commands should be applied to all newly compiled X60 ROM images (the ROM images in libreboot binary archives already have this applied!):<br/>
dd if=coreboot.rom of=top64k.bin bs=1 skip=$[$(stat -c %s coreboot.rom) - 0x10000] count=64k<br/>
dd if=coreboot.rom bs=1 skip=$[$(stat -c %s coreboot.rom) - 0x20000] count=64k | hexdump<br/>
dd if=top64k.bin of=coreboot.rom bs=1 seek=$[$(stat -c %s coreboot.rom) - 0x20000] count=64k conv=notrunc<br/>
(doing this makes the ROM suitable for use when flashing a system that still has Lenovo BIOS running,
using those instructions: <a href="http://www.coreboot.org/Board:lenovo/x60/Installation">http://www.coreboot.org/Board:lenovo/x60/Installation</a>.
</p>
</div>
<div class="section">
<h1 id="recovery">bad rom (or user error), system won't boot</h1>
<p>
In this scenario, you compiled a ROM that had an incorrect configuration, or there is an actual bug preventing your system from
booting. Or, maybe, you set BUC.TS to 0 and shut down after first flash while Lenovo BIOS was running. In any case, your system is bricked and will not boot at all.
</p>
<p>
"Unbricking" means flashing a known-good (working) ROM. The problem: you can't boot the system, making this difficult. In this situation, external hardware (see hardware requirements above) is needed which can flash the SPI chip (where libreboot resides).
</p>
<p>
Remove those screws:<br/>
<img src="../images/x60_unbrick/0000.jpg" alt="" />
</p>
<p>
Push the keyboard forward (carefully):<br/>
<img src="../images/x60_unbrick/0001.jpg" alt="" />
</p>
<p>
Lift the keyboard up and disconnect it from the board:<br/>
<img src="../images/x60_unbrick/0002.jpg" alt="" />
</p>
<p>
Grab the right-hand side of the chassis and force it off (gently) and pry up the rest of the chassis:<br/>
<img src="../images/x60_unbrick/0003.jpg" alt="" />
</p>
<p>
You should now have this:<br/>
<img src="../images/x60_unbrick/0004.jpg" alt="" />
</p>
<p>
Disconnect the wifi antenna cables, the modem cable and the speaker:<br/>
<img src="../images/x60_unbrick/0005.jpg" alt="" />
</p>
<p>
Unroute the cables along their path, carefully lifting the tape that holds them in place. Then, disconnect the modem
cable (other end) and power connection and unroute all the cables so that they dangle by the monitor hinge on the right-hand
side:<br/>
<img src="../images/x60_unbrick/0006.jpg" alt="" />
</p>
<p>
Disconnect the monitor from the motherboard, and unroute the grey antenna cable, carefully lifting the tape
that holds it into place:<br/>
<img src="../images/x60_unbrick/0008.jpg" alt="" />
</p>
<p>
Carefully lift the remaining tape and unroute the left antenna cable so that it is loose:<br/>
<img src="../images/x60_unbrick/0009.jpg" alt="" />
</p>
<p>
Remove the screw that is highlighted (do NOT remove the other one; it holds part of the heatsink (other side) into place):<br/>
<img src="../images/x60_unbrick/0011.jpg" alt="" />
</p>
<p>
Remove those screws:<br/>
<img src="../images/x60_unbrick/0012.jpg" alt="" />
</p>
<p>
Carefully remove the plate, like so:<br/>
<img src="../images/x60_unbrick/0013.jpg" alt="" />
</p>
<p>
Remove the SATA connector:<br/>
<img src="../images/x60_unbrick/0014.jpg" alt="" />
</p>
<p>
Now remove the motherboard (gently) and cast the lcd/chassis aside:<br/>
<img src="../images/x60_unbrick/0015.jpg" alt="" />
</p>
<p>
Lift back that tape and hold it with something. Highlighted is the SPI flash chip:<br/>
<img src="../images/x60_unbrick/0016.jpg" alt="" />
</p>
<p>
Now wire up the BBB and the Pomona with your PSU.<br/>
Refer to <a href="bbb_setup.html">bbb_setup.html</a> for how to setup
the BBB for flashing.<br/>
<b>Note, the guide mentions a 3.3v DC PSU but you don't need this on the X60:
if you don't have or don't want to use an external PSU, then make
sure not to connect the 3.3v leads mentioned in the guide;
instead, connect the AC adapter (the one that normally charges your
battery) so that the board has power (but don't boot it up)</b>
<img src="../images/x60_unbrick/0017.jpg" alt="" /><br/>
Correlate the following with the BBB guide linked above:
</p>
<pre>
POMONA 5250:
=== golden finger and wifi switch ====
18 - - 1
22 - - NC ---------- audio jacks are on this end
NC - - 21
3.3V (PSU) - - 17 - this is pin 1 on the flash chip
=== CPU fan ===
<i>This is how you will connect. Numbers refer to pin numbers on the BBB, on the plugs near the DC jack.</i>
</pre>
<p>
Connecting the BBB and pomona (in this image, an external 3.3v DC PSU was used):<br/>
<img src="images/x60/th_bbb_flashing.jpg" alt="" />
</p>
<p>
Flashrom binaries for ARM (tested on a BBB) are distributed in libreboot_util. Alternatively,
libreboot also distributes flashrom source code which can be built.
</p>
<p>
SSH'd into the BBB:<br/>
# <b>./flashrom -p linux_spi:dev=/dev/spidev1.0,spispeed=512 -w yourrom.rom</b>
</p>
<p>
It should be <b>Verifying flash... VERIFIED</b> at the end. If flashrom complains about multiple flash chip
definitions detected, then choose one of them following the instructions in the output.
</p>
<p>
Remove the programmer and put it away somewhere. Put back the tape and press firmly over it:<br/>
<img src="../images/x60_unbrick/0026.jpg" alt="" />
</p>
<p>
Your empty chassis:<br/>
<img src="../images/x60_unbrick/0027.jpg" alt="" />
</p>
<p>
Put the motherboard back in:<br/>
<img src="../images/x60_unbrick/0028.jpg" alt="" />
</p>
<p>
Reconnect SATA:<br/>
<img src="../images/x60_unbrick/0029.jpg" alt="" />
</p>
<p>
Put the plate back and re-insert those screws:<br/>
<img src="../images/x60_unbrick/0030.jpg" alt="" />
</p>
<p>
Re-route that antenna cable around the fan and apply the tape:<br/>
<img src="../images/x60_unbrick/0031.jpg" alt="" />
</p>
<p>
Route the cable here and then (not shown, due to error on my part) reconnect the monitor cable to the motherboard
and re-insert the screws:<br/>
<img src="../images/x60_unbrick/0032.jpg" alt="" />
</p>
<p>
Re-insert that screw:<br/>
<img src="../images/x60_unbrick/0033.jpg" alt="" />
</p>
<p>
Route the black antenna cable like so:<br/>
<img src="../images/x60_unbrick/0034.jpg" alt="" />
</p>
<p>
Tuck it in neatly like so:<br/>
<img src="../images/x60_unbrick/0035.jpg" alt="" />
</p>
<p>
Route the modem cable like so:<br/>
<img src="../images/x60_unbrick/0036.jpg" alt="" />
</p>
<p>
Connect modem cable to board and tuck it in neatly like so:<br/>
<img src="../images/x60_unbrick/0037.jpg" alt="" />
</p>
<p>
Route the power connection and connect it to the board like so:<br/>
<img src="../images/x60_unbrick/0038.jpg" alt="" />
</p>
<p>
Route the antenna and modem cables neatly like so:<br/>
<img src="../images/x60_unbrick/0039.jpg" alt="" />
</p>
<p>
Connect the wifi antenna cables. At the start of the tutorial, this system had an Intel wifi chip. Here you see I've replaced it with an
Atheros AR5B95 (supports 802.11n and can be used without blobs):<br/>
<img src="../images/x60_unbrick/0040.jpg" alt="" />
</p>
<p>
Connect the modem cable:<br/>
<img src="../images/x60_unbrick/0041.jpg" alt="" />
</p>
<p>
Connect the speaker:<br/>
<img src="../images/x60_unbrick/0042.jpg" alt="" />
</p>
<p>
You should now have this:<br/>
<img src="../images/x60_unbrick/0043.jpg" alt="" />
</p>
<p>
Re-connect the upper chassis:<br/>
<img src="../images/x60_unbrick/0044.jpg" alt="" />
</p>
<p>
Re-connect the keyboard:<br/>
<img src="../images/x60_unbrick/0045.jpg" alt="" />
</p>
<p>
Re-insert the screws that you removed earlier:<br/>
<img src="../images/x60_unbrick/0046.jpg" alt="" />
</p>
<p>
Power on!<br/>
<img src="../images/x60_unbrick/0047.jpg" alt="" />
</p>
<p>
Trisquel live USB menu (using the GRUB ISOLINUX parser):<br/>
<img src="../images/x60_unbrick/0048.jpg" alt="" />
</p>
<p>
Trisquel live desktop:<br/>
<img src="../images/x60_unbrick/0049.jpg" alt="" />
</p>
</div>
<div class="section">
<p>
Copyright © 2014, 2015 Leah Rowe <info@minifree.org><br/>
Permission is granted to copy, distribute and/or modify this document
under the terms of the Creative Commons Attribution-ShareAlive 4.0 International license
or any later version published by Creative Commons;
A copy of the license can be found at <a href="../cc-by-sa-4.0.txt">../cc-by-sa-4.0.txt</a>
</p>
<p>
Updated versions of the license (when available) can be found at
<a href="https://creativecommons.org/licenses/by-sa/4.0/legalcode">https://creativecommons.org/licenses/by-sa/4.0/legalcode</a>
</p>
<p>
UNLESS OTHERWISE SEPARATELY UNDERTAKEN BY THE LICENSOR, TO THE
EXTENT POSSIBLE, THE LICENSOR OFFERS THE LICENSED MATERIAL AS-IS
AND AS-AVAILABLE, AND MAKES NO REPRESENTATIONS OR WARRANTIES OF
ANY KIND CONCERNING THE LICENSED MATERIAL, WHETHER EXPRESS,
IMPLIED, STATUTORY, OR OTHER. THIS INCLUDES, WITHOUT LIMITATION,
WARRANTIES OF TITLE, MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, NON-INFRINGEMENT, ABSENCE OF LATENT OR OTHER DEFECTS,
ACCURACY, OR THE PRESENCE OR ABSENCE OF ERRORS, WHETHER OR NOT
KNOWN OR DISCOVERABLE. WHERE DISCLAIMERS OF WARRANTIES ARE NOT
ALLOWED IN FULL OR IN PART, THIS DISCLAIMER MAY NOT APPLY TO YOU.
</p>
<p>
TO THE EXTENT POSSIBLE, IN NO EVENT WILL THE LICENSOR BE LIABLE
TO YOU ON ANY LEGAL THEORY (INCLUDING, WITHOUT LIMITATION,
NEGLIGENCE) OR OTHERWISE FOR ANY DIRECT, SPECIAL, INDIRECT,
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY, OR OTHER LOSSES,
COSTS, EXPENSES, OR DAMAGES ARISING OUT OF THIS PUBLIC LICENSE OR
USE OF THE LICENSED MATERIAL, EVEN IF THE LICENSOR HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH LOSSES, COSTS, EXPENSES, OR
DAMAGES. WHERE A LIMITATION OF LIABILITY IS NOT ALLOWED IN FULL OR
IN PART, THIS LIMITATION MAY NOT APPLY TO YOU.
</p>
<p>
The disclaimer of warranties and limitation of liability provided
above shall be interpreted in a manner that, to the extent
possible, most closely approximates an absolute disclaimer and
waiver of all liability.
</p>
</div>
</body>
</html>
|
